How to quickly clean gutters and sewers?

Sink and downspout are one of the simpler and more reliable drainage systems, they work only by gravity and will hardly wear out. When they fail, the reason is the same, probably 99% of the time, that we fail to clean them up. Aside from immediate damage, the only system failures they suffered were improper slopes, sinking gutters and not sloping downpipes.

So, the best way to keep your gutters working is to get up and clean them, at least a few times a year. Even if you install screens or other devices to keep debris out of your gutters, you'll want to check them regularly to make sure they're not clogged. Unless cleaned, roof gutters can become clogged with debris, preventing them from functioning properly.

For a single-level drainage system, the best ladder for cleaning the sink is a tall ladder. This provides a good range of motion without compromising stability and is generally easier to move than a telescopic ladder. For a multi-level drainage system, you will need a telescopic ladder. In this case, make sure the feet of the ladder are on firm, level ground or use a brick to level the feet, and the ladder is sloped toward the house at a 75-degree angle.

You should be able to reach the gutters without standing on the top rung of the ladder, be sure to wear heavy work gloves to clean the gutters. There are lots of sharp metal edges and viciously pointed sheet metal screws hidden behind all the junk. If you are using a hose for any spraying, especially with a gutter cleaning stick, you may need to wear safety glasses.

How to clean gutters

The number one trick to clearing gutters is to do so often, and before the next big storm. The standard recommended time is twice a year, but if you have large trees near your roof, you may need to check your gutters frequently, at least a few times in the fall, and every few months for the rest of the year Check once.

To clean the sink, wear work gloves and grab an 18.9-liter bucket with a handle. You can use a small spatula or a toilet brush to scoop up the goo in the sink if needed, but usually your hands are just as good. Start with one of the downspouts and work on the other end of the sink.

Most blockages are extremely severe near downspout openings, and if there is standing water in the gutter, cleaning the entrance to the downspout can allow the water to flow out while you work.

Throw a handful of scraps into the bucket, and if needed, you can hang the bucket on the hook of the ladder so you don't have to mention it. When the bucket is full or heavy, move it to the ground and dump it into a trash bag or compost pile. Once the debris has been removed, you can take cleaning to another level by blasting the gutters with a garden hose and nozzle.

In this case, start at the high end of the gutter and use the downspout opening to spray towards the end. Spraying is not necessary in most cases, but it's a good idea if the gutters are muddy or if there is a lot of mineral particles built up on the roof tiles.

Tips for cleaning downspouts

If your gutters are particularly dirty or you suspect one is clogged in a downspout, flush it with a garden hose. Feed one end of the hose into the bottom of the drain and open the hose all the way.

Be careful not to damage any sharp sheet metal screws on the hose that could poke into the inside of the downspout. Move the hose further up until the blockage is completely cleared. If the blockage is really stubborn, you may have to insert the hose from the top down, or the hose down from the bottom.

Regarding those sheet metal screws, for whatever reason, the metal gutter industry has not been able to come up with a better system than driving the screws directly into the downspout's runners, which tend to attract leaves and debris, effectively effectively Reduced the capacity of the water pipe. It's a pretty bad design, but it does just that.

Even more problematic is when gutter installers use long screws for downspout joints. Ideally, these screws should be no more than 1.5cm long, but you may find 2cm or 2.5cm screws, and if you do, replace them with shorter screws to reduce the chance of clogging.